欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Machining titanium alloy is hard because the thermal conductivity of titanium alloy is very poor. Coupled with the short contact length between the chip and the cutting tool, it is not conducive to the dissipation of cutting heat. As a result, the temperature in the cutting edge region is high, about more than twice that of cutting 45 steel. In addition, tool wear is also severe. On the one hand, the strong chemical affinity between titanium alloy and tool material makes it easy to bond with elements such as Ti, Co, and C in the tool material, aggravating adhesive wear at high temperatures. On the other hand, titanium alloy easily forms a hard and brittle surface layer by reacting with oxygen and nitrogen in the air, exacerbating tool wear.

Table 1: Selection of Tool Geometric Parameters for Turning Titanium Alloys

Tool material Front Rake Angle ?Back Rake Angle Cutting Edge Inclination Angle Main Clearance Angle Secondary Clearance Angle Chamfer Width (mm) Chamfer Front Angle Cutting Edge Radius (mm)
Carbide lathe 5~10 10~15 0~10 45~75 15 0.05~0.3 0.10~0 0.5~1.5

What are the Challenges in Machining Titanium Alloys? 1

Machining amount

The cutting speed for turning titanium alloys should not be too high, and the cutting depth can be relatively large, while the feed rate should be appropriate. A feed rate that is too large can cause burning of the cutting edge, while a feed rate that is too small results in rapid wear of the cutting edge when processing the hardened layer. When turning titanium alloys, rust-proof emulsion or extreme-pressure emulsion can be used for cooling and lubrication. The recommended cutting parameters for turning titanium alloys are as shown in

Table 2: Selection of Cutting Parameters for Turning Titanium Alloys

Feed (mm) cutting speed(mm)
0.08~0.12 87~69
0.13~0.17 71~59
0.16~0.24 62~51
0.25~0.30 53~47
0.33~0.44 48~41
0.45~0.65 42~34

Note: Conditions for the use of this table: Tool material YG8, workpiece material TC4, tool geometric angles front rake angle = 5°, back rake angle = 10°, main clearance angle = 75°, secondary clearance angle = 15°, cutting edge radius = 0.5mm, turning depth = 1mm, dry turning. If using cutting fluid, the turning speed in the table can be appropriately increased.

What are the Challenges in Machining Titanium Alloys? 2

Machining parameters

Machining Temp.

When turning titanium alloys, the cutting temperature is high, and tool durability is low. Among the cutting parameters, cutting speed has the most significant impact on cutting temperature. Therefore, efforts should be made to ensure that the cutting temperature generated at the selected cutting speed is within the optimal range. The recommended cutting temperature for turning titanium alloys with high-speed steel tools is approximately 480°C to 540°C, while for hard alloy tools, it is around 650°C to 750°C.

Cutting speed Vc

The cutting speed has the most significant impact on tool durability, and it is preferable to operate the tool at the optimal cutting speed with minimal relative wear. When turning titanium alloys of different grades, the cutting speed should be adjusted appropriately due to significant differences in strength. The turning depth also has a certain influence on the cutting speed, and the magnitude of the cutting speed should be determined based on different turning depths.

Feed rate

The feed rate has a relatively small impact on tool durability. While ensuring the machining surface roughness, a larger feed rate can be chosen, typically ranging from f=0.1 to 0.3 mm/r. If the feed rate is too small, the tool may cut within the hardened layer, increasing tool wear. Additionally, extremely thin chips are prone to spontaneous combustion at high cutting temperatures, so a feed rate below f<0.05 mm/r is not allowed.

Cutting depth (ap) has the least impact on tool durability. A larger cutting depth is generally chosen to avoid cutting within the hardened layer, reducing tool wear. It also increases the working length of the cutting edge, promoting heat dissipation. Typically, ap is set at 1 to 5 mm.

Tr? l?i

Email c?a b?n s? kh?ng ???c hi?n th? c?ng khai. Các tr??ng b?t bu?c ???c ?ánh d?u *

亚洲女同一区二区三久久精品| 美女被插进去黄色| 男人把鸡巴插入女人| 亚洲一区二区三区日本在线| 操老骚逼三级黄视频| 欧美 日韩 国产 自拍| 几巴怪物操逼视频| 亚洲精品一区二区精华液| 大肉棒操小骚穴视频| 国产精品一区二区三区在线视| A级毛片毛片免费观看久| 熟妇人妻无乱码中文字幕| 手机成人三级a在线观看| 92婷婷伊人久久精品一区二区| 夫妻性生活在线免费视频| 精品人妻少妇一区二区三区不卡| 丁香婷婷色婷婷粗大| 黑人与日本人妻中文字幕| 天堂丝袜人妻中文字幕在线| 国产无圣光一区福利二区| 国产精品久久一区二区三区动| 黑人大鸡把操逼视频| 亚洲精品国产综合一线久久| 国产黄片在线免费看| 欧美十八一区二区三区| 白嫩在线亚洲观看| 精品免费福利片国产| 99久久久国产精品美女| 国产又粗又猛又色又免费| 视频在线观看一区@99| 欧美一区二区三区色婷婷月色| 久久久久九九九国产精品| 久久精品国产亚洲高清| 成人区久久精品一区二区| 国产精品无码毛片久久久| 黄色av成年人在线观看| 把美女日到高潮喷水视频| 男人插女人视频软件| 美国业余自由摘花管| 男人大鸡巴操女人的大逼| 欧美老熟妇又粗又大|