欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Metal processing is inseparable from the blade. A good blade must have high wear resistance, long tool life, high metal removal rate and high reliability. It is even required to have high performance in dry cutting or wet cutting under severe conditions (such as complex cutting and deep cavity), so as to ensure small tolerance of workpiece size and excellent surface quality. Today, let’s take a look at how the leader of the blade industry produces blades

How to make blade tolerance accurate

A typical blade is made of 80% tungsten carbide and metal matrix. The function of metal matrix is to bond hard cemented carbide powder together, of which cobalt is the most common. The process of producing blades is very complex. It takes more than two days to complete, and there will be a lot of challenges. In addition to absolute precision and reliability, cleanliness is a prerequisite. The whole process must be well guaranteed without any carelessness.

The first step is to ensure that the composition ratio of each specific powder is just right. Tungsten is a limited raw material derived from Sandvik’s mine in Austria or recycled blade. Cobalt, titanium and all other components come from carefully selected suppliers who can ensure consistent quality without affecting the quality of finished products. Nevertheless, every batch must be meticulously tested in the laboratory for safety. The main components are then automatically distributed to containers at different stations along the weighing line. For some blades, a small amount of special ingredients need to be added manually. After passing through all the different stations, the full container will weigh hundreds of kilograms.

Why are Good Insers Expensive? 2

The next step is grinding, mixing the components in the container with ethanol, water and organic compounds, and grinding them to the required particle size: usually 0.1 ~ 5 microns in diameter. This process takes 8 ~ 55 hours, depending on the formula of the finished product. The compound is a gray slurry with a consistency similar to that of yogurt drinks. Then the slurry is pumped into the spray dryer, and the spray dryer evaporates the mixture of ethanol and water with hot nitrogen.

When the powder is dried, it consists of spherical particles with a diameter of about 100 microns. The samples were sent to the laboratory for quality inspection. Then, the ready-made powder is filled into a smaller barrel and processed by pressing machine, in which the organic compound acts as an adhesive, and the powder is bonded together after pressing. After the mold of a specific blade is in place, the inner cavity of the mold will be filled with powder. The machine tool can apply 50 tons of pressure when manufacturing a single blade. Even if the automation of the whole process is high, each blade will still be weighed, and then the operator will carry out appearance control at certain time intervals to ensure the highest quality and accuracy. At this stage, the blade is still very fragile, so the next step is to enter the sintering furnace.

Why is sintering a complicated process

Why are Good Insers Expensive? 3

The sintering furnace can sinter thousands of blades at a time. The blade is heated to about 1500 ℃, in which the process takes about 13 hours, and the pressed powder is melted into cemented carbide, which is an extremely hard material. However, this process will lead to serious shrinkage: the size of the sintered blade is only about half the size of the pressed part. After being sent to the laboratory again for quality inspection, grind the top and bottom of the blade to the correct thickness. Because cemented carbide is very hard, it is necessary to use a grinding wheel containing 150 million small industrial diamond particles to grind it to the correct thickness. Usually, the blade has to be polished again to achieve its accurate groove shape and size.

This is a key step in the manufacturing process. The use of 6-axis grinder can ensure very strict tolerance, so that there has been a joke in Kimmer factory: “if you sneeze, the tolerance will change immediately”.

Clean and coat the blade immediately after grinding. To avoid any grease or dust, gloves must be worn when taking the blade. There are two different coating methods of blade coating: chemical vapor deposition (CVD) and physical vapor deposition (PVD). In a typical CVD, the blade substrate is contacted with one or more volatile coating gases, which react on the surface of the blade substrate to generate the required deposits. The physical vapor depositio

Bir cevap yaz?n

E-posta hesab?n?z yay?mlanmayacak. Gerekli alanlar * ile i?aretlenmi?lerdir

美女被插入小穴涩涩视频| 人人超级碰青青精品| 啊啊啊别操了视频| 欧美日韩久久久一区二区三区| 玖玖资源站无码专区| 成人刺激性视频在线观看| 日韩av一区二区三区激情在线| 97超视频免费在线观看| 市长含着秘书的奶头| 久久久久有精品国产麻豆| 96精品久久久久久蜜臀浪| 国产羞羞的视频在线观看| 日韩精品诱惑一区?区三区| 亚洲欧美日韩另类| 国产精品欧美久久久久久| 三级成人国产高清视频| 国产91视频观看| 黑人巨茎和中国美女视频| av在线国产哟哟| 裸体美女被操的啊啊直叫| 波多野结衣浴尿解禁在线| 亚洲精品国产人久久| 韩国无玛黄片毛片| 大鸡巴抽插小骚逼视频免费| 大鸡巴操逼视频免费| 亚洲国产一区二区不卡在线资源| 精品国产自在现线看| 国产精品视频一区二区三区分享| 一区二中文字幕在线看国产一区| 黑丝美女被操到高潮| 91大神精品动漫| 浪潮AV色综合久久天堂| 骚狐狸免费在线观看视频| 最新免费高清无码片| 黄网官方在线观看| 精品麻豆亚洲欧美| 国产一国产一级毛片无码视频百度| 在线免费观看一区二区三区| 高清最新操逼吃鸡巴视频| 男女真人牲交高潮全过程| 亚洲午夜av一区二区三区|