欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Milling process is essentially a kind of intermittent processing process. This causes the temperature at the cutting edge to fluctuate between high temperature (about 1000 ℃) and low temperature.

Effect of cutting fluid

When the cutting edge cuts in and cuts out, the temperature change will increase. As a result, the cutting edge is subject to thermal shock and periodic stresses, which may result in cracks and, in the worst case, premature end of tool life.

The higher the temperature of the cutting area, the less suitable the cutting fluid is.

In the finishing process, the use of cutting fluid will not shorten the tool life as much as in rough machining due to the reduced heat generated.

When to Use Wet Milling or Dry Milling? 2
Hot cracks on cutting edge

dry milling

Dry milling can prolong the life of cutting edge. The temperature does change, but it will remain within the design range of cemented carbide materials.

Rough milling should always be carried out without cutting fluid.

wet milling with cutting fluid

There are some exceptions to the use of cutting fluid:

1) Finish machining of stainless steel and aluminum alloys – used to prevent metal particles from sticking to the surface structure

2) Milling superalloys at low cutting speeds – for lubrication and cooling of parts

3) Cast iron milling, used to wet and remove dust to protect the environment and health and ensure the accuracy of parts

4) Milling of thin wall parts to prevent geometric deformation

5) When machining deep cavity, micro lubrication system (i.e. compressed air containing a small amount of special oil) can be used to assist chip removal

When to Use Wet Milling or Dry Milling? 3
Use compressed air and oil mist

In the micro lubrication system, the “oil mist” is only a few milliliters of oil per hour, and is discharged through the ordinary filtering ventilation system.

When to Use Wet Milling or Dry Milling? 4
Use a large flow of internal and external coolant

If wet milling must be carried out, a sufficient amount of cutting fluid should be used.

日韩欧美视频在线观看不卡| 大黑屌狂操骚逼视频| 国内揄拍国内精品| 黄色免费老人操逼| 日本成人精品一区二区三区| 美女露胸露逼逼自慰| 狠狠五月激情综合去干网| 国产成人无码AV一区二区三区| 亚洲福利左线观看| 国产一区二区三区午夜精品久久| 大鸡巴操小逼的视频| 狗狗大鸡巴狂操美女| 黄片大鸡吧操小逼| 欧美日韩亚洲人人夜夜澡| 国产精品欧美久久久久久| 久久精品男人的天堂av| 新视觉亚洲三区二区一区理伦| 女人被躁到高潮嗷嗷叫小| 性色av一区二区三区天美传媒四| 精品免费在线观看等| 啊好爽好多水深插射视频| 91麻豆精品福利在线观看| 91精品国产剧情欧美一区二区| 国产欧美一二区不卡视频| 欧美日本欧美日本区一区二| av中文字幕一区二区精品久久| 黄片大鸡吧操小逼| 国产欧美日韩一区二区在线观看| 久久久中文字幕一区| 无码中文字幕免费一区二区三区| 国产高清乱码女大生AV| 国产无圣光一区福利二区| 日本一二区视频在线观看| 美女日比视频播放| 亚洲免费福利视频| 又爽又粗又大又长的爆草| 亚洲一区亚洲二区在线观看| 无码人妻免费一区二区三区| 亚洲精品一区二区精华液| 操老女人大逼视频| 大鸡巴狂插嫩逼视频|