欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

Machining titanium alloy is hard because the thermal conductivity of titanium alloy is very poor. Coupled with the short contact length between the chip and the cutting tool, it is not conducive to the dissipation of cutting heat. As a result, the temperature in the cutting edge region is high, about more than twice that of cutting 45 steel. In addition, tool wear is also severe. On the one hand, the strong chemical affinity between titanium alloy and tool material makes it easy to bond with elements such as Ti, Co, and C in the tool material, aggravating adhesive wear at high temperatures. On the other hand, titanium alloy easily forms a hard and brittle surface layer by reacting with oxygen and nitrogen in the air, exacerbating tool wear.

Table 1: Selection of Tool Geometric Parameters for Turning Titanium Alloys

Tool material Front Rake Angle ?Back Rake Angle Cutting Edge Inclination Angle Main Clearance Angle Secondary Clearance Angle Chamfer Width (mm) Chamfer Front Angle Cutting Edge Radius (mm)
Carbide lathe 5~10 10~15 0~10 45~75 15 0.05~0.3 0.10~0 0.5~1.5

What are the Challenges in Machining Titanium Alloys? 1

Machining amount

The cutting speed for turning titanium alloys should not be too high, and the cutting depth can be relatively large, while the feed rate should be appropriate. A feed rate that is too large can cause burning of the cutting edge, while a feed rate that is too small results in rapid wear of the cutting edge when processing the hardened layer. When turning titanium alloys, rust-proof emulsion or extreme-pressure emulsion can be used for cooling and lubrication. The recommended cutting parameters for turning titanium alloys are as shown in

Table 2: Selection of Cutting Parameters for Turning Titanium Alloys

Feed (mm) cutting speed(mm)
0.08~0.12 87~69
0.13~0.17 71~59
0.16~0.24 62~51
0.25~0.30 53~47
0.33~0.44 48~41
0.45~0.65 42~34

Note: Conditions for the use of this table: Tool material YG8, workpiece material TC4, tool geometric angles front rake angle = 5°, back rake angle = 10°, main clearance angle = 75°, secondary clearance angle = 15°, cutting edge radius = 0.5mm, turning depth = 1mm, dry turning. If using cutting fluid, the turning speed in the table can be appropriately increased.

What are the Challenges in Machining Titanium Alloys? 2

Machining parameters

Machining Temp.

When turning titanium alloys, the cutting temperature is high, and tool durability is low. Among the cutting parameters, cutting speed has the most significant impact on cutting temperature. Therefore, efforts should be made to ensure that the cutting temperature generated at the selected cutting speed is within the optimal range. The recommended cutting temperature for turning titanium alloys with high-speed steel tools is approximately 480°C to 540°C, while for hard alloy tools, it is around 650°C to 750°C.

Cutting speed Vc

The cutting speed has the most significant impact on tool durability, and it is preferable to operate the tool at the optimal cutting speed with minimal relative wear. When turning titanium alloys of different grades, the cutting speed should be adjusted appropriately due to significant differences in strength. The turning depth also has a certain influence on the cutting speed, and the magnitude of the cutting speed should be determined based on different turning depths.

Feed rate

The feed rate has a relatively small impact on tool durability. While ensuring the machining surface roughness, a larger feed rate can be chosen, typically ranging from f=0.1 to 0.3 mm/r. If the feed rate is too small, the tool may cut within the hardened layer, increasing tool wear. Additionally, extremely thin chips are prone to spontaneous combustion at high cutting temperatures, so a feed rate below f<0.05 mm/r is not allowed.

Cutting depth (ap) has the least impact on tool durability. A larger cutting depth is generally chosen to avoid cutting within the hardened layer, reducing tool wear. It also increases the working length of the cutting edge, promoting heat dissipation. Typically, ap is set at 1 to 5 mm.

Bir cevap yaz?n

E-posta hesab?n?z yay?mlanmayacak. Gerekli alanlar * ile i?aretlenmi?lerdir

你懂的在线中文字幕一区| 一级美女插逼百度| 国产精品操大屁股老淑女| 亚洲波多野结衣日韩在线| 大肉棒插了按摩视频| 怎么样操女人的逼亚洲Av黄片段| 欧美日韩一级视频| 无码爆一二三区免费视频| 日韩欧美综合一二三区| 白丝袜子宫啊啊啊不要了| 美女被插进去黄色| 国产精品久久一区二区三区动| 大肉棒操小骚穴视频| 男人和女人干污污| 99视频在线看免费视频| 中文国产成人精品久久久| 男插女下面高潮视频| 欧美大鸡巴操穴日韩| 极品一区二区三区av| 欧美国产日韩a欧美在线| 男人操女人下面国产剧情| 中文字幕在线视频一区二区| 久久精品一区二区三区免费看| 中文字幕人妻一区二区三区人妻| 精品v欧洲高清欧美| 亚洲欧美日韩精品一区二区| 欧美黑屌操B内射冒白浆| 91大神精品动漫| 中文字幕乱码一区三区免费| 国产亚洲情侣久久精品| 男插女下面高潮视频| 欧美精品性做久久久久久| 亚洲男性天堂一区二区三区| 九九在线视频热线视频精选| 久久久久久国产A免费观看| 一级特黄大片色欧美精品| 9亚洲导航深夜福利亚洲| 国产大码丝袜老熟女av| AV天堂手机福利网| 国产精品亚洲1区2区| 久久久精品国产乱码内射|