欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

The processed product is a bevel gear with 16 φ17 through-holes, made of sticky metal material with a hardness in the range of HB165-190 and containing a certain amount of Ni element. Given the characteristics of the workpiece, selecting appropriate drill bits, optimizing cutting parameters, and improving processing efficiency are the top priorities.

Selection of Drill Bit Material

According to the processing characteristics of the material, the drill bits are required to have the following features:

1.The hardness of the drill bit must be greater than that of the workpiece being processed.

2.Since the drill bit undergoes significant torsional and axial forces during machining, it must have sufficient strength and toughness. Due to the good toughness of the processed material, sharp cutting edges are required to reduce work hardening. Therefore, the tool material must have sufficient wear resistance to minimize machining hardening.

3.Due to the high chemical properties of the workpiece, it is required that the tool material has poor affinity with titanium alloys to prevent diffusion bonding and tool sticking or drill breakage phenomena.

Currently, there is a wide variety of materials suitable for tool manufacturing, including tool steel, cemented carbide, and superhard materials.

Initially, attempts were made to use ordinary high-speed steel drill bits with coatings for experimentation. Ordinary high-speed steel drill bits are inexpensive, and with the use of coating technology, the friction coefficient between the tool and the workpiece can be significantly reduced, thus improving tool life. However, due to the high spindle speed of the machine tool and insufficient strength of the drill bits used, the drill bits broke during the machining process, yielding unsatisfactory results.

Cemented carbide is a newly developed tool material suitable for rough and finish machining of most materials, including steel, cast iron, special materials, and plastics. Therefore, it was decided to use solid cemented carbide drill bits.

drill bit for sticky material

Determination of Drill Bit Grinding Parameters

Main auxiliary planes of twist drill

The main auxiliary planes of a twist drill include the base plane, cutting plane, median plane, and cylindrical plane. If auxiliary motions are not considered, the base plane of any point on the main cutting edge of the twist drill varies due to the architectural characteristics of the twist drill.

The cutting plane at any point on the main cutting edge is a plane containing the cutting speed direction of that point and cutting the machined surface at that point. The cutting plane is perpendicular to the base plane, and the cutting planes at different points on the main cutting edge are different.

The cylindrical plane at any point on the main cutting edge is a cylindrical surface made through that point and with the drill axis as the center line, with different radii for different cylindrical planes.

How to Select Suitable Cemented Carbide Drill Bits for Sticky Metal Materials 2

Selection of main geometric parameters of twist drill

The selection of main geometric parameters of twist drill includes the choice of drill point angle, the choice of drill cutting edge front and back angles, analysis of the influence of drill spiral angle on drill life, and relevant treatments of the cutting edge. The drill point angle determines the width of the chip and the size of the drill cutting edge front angle.

When the drill diameter and feed rate are constant, increasing the point angle makes the chips narrower, reducing the load per unit cutting edge. The point angle has a significant influence on the front angle. Increasing the point angle is conducive to improving the cutting conditions at the drill center. The point angle affects the direction of chip flow. Based on relevant tool design data and considering the low hardness but high stickiness of the processed product, the drill point angle was chosen as 140°.

The front angle of the twist drill is determined by other geometric parameters of the drill bit. During high-speed cutting on the machine tool, the front angle has a minor effect on cutting deformation and cutting force. Using a smaller front angle can enhance the tip strength. After determining the front angle, the larger the back angle, the sharper the cutting edge, but it will correspondingly reduce the wedge angle, affecting the strength and heat dissipation area of the tool. Therefore, a slightly smaller back angle of 8° was selected for the drill bit.

How to Select Suitable Cemented Carbide Drill Bits for Sticky Metal Materials 3

Analysis of the influence of drill spiral angle on drill life

From the external characteristics of the twist drill, it can be known that the spiral angle at each point on the cutting edge is variable, directly affecting the front angle of the main cutting edge. The larger the spiral angle, the sharper the cutting edge, and the lighter the cutting, otherwise, it will cause severe work hardening, leading to rapid wear of the cutting edge. Based on relevant tool design data, a spiral angle of 30° was chosen to meet usage requirements and facilitate mass production.

 

Relevant treatment of the cutting edge

The treatment of the cutting edge includes measures such as transverse edge correction, chamfering, and counter-edge. Suitable blunting of the drill bit’s cutting edge was carried out according to the processed material, machine tool performance, machining parameters, and fixture conditions, improving the drilling performance of the drill bit and reducing tool wear.

 

Application of Coating Technology

With the cutting parameters unchanged, in order to improve production efficiency and reduce production costs, coating technology has become a trend for tool application, reducing tool wear to increase tool durability. Tool coating refers to the deposition of a thin layer of wear-resistant refractory metal or non-metallic compound on the surface of a cemented carbide or high-speed steel (HSS) matrix using a gas-phase deposition method. As a chemical and thermal barrier, the coating reduces diffusion and chemical reactions between the tool and the workpiece, thereby reducing tool wear. Coated tools have characteristics such as high surface hardness, good wear resistance, stable chemical properties, heat resistance, oxidation resistance, low friction coefficient, and low thermal conductivity. After coating, the number of drill bits processed has significantly increased, and the unit cost has been greatly reduced.

Добавить комментарий

Ваш адрес email не будет опубликован. Обязательные поля помечены *

男男大鸡巴操小屁眼视频| 阴茎大头插少妇蜜穴视频| 91kaobi视频在线| 欧美亚洲干妞内射| 欧美精品国产一区二区在线观看| 日韩欧美综合一二三区| 日韩美女一区二区三区香蕉视频| 少妇被黑人入侵在线观看| 日本入室强伦姧人妻中文| 亚洲国产成久久成人综合一区| 老司机精品免费在线视频| 中日韩VA无码中文字幕| 丰满少妇被强入在线观看| 少妇精品久久久一区二区免费| 三级片成人京东热五月天| 久久国产亚洲高清| 777米奇在线视频无码| 国产精品视频一区二区三区分享| 国产成人精品区在线观看| 日韩素人精品亚洲热一区| 免费看看小骚逼逼| 波多野结衣高潮尿喷| 国产精品久久大屁股白浆| 一级做a爱过程免费视频俩| 极品一区二区三区av| 日韩美女叉B视频| 看人妻仑乱A级毛片| 中文字幕 av一区二区| 天天天天天干夜夜夜夜夜操| 91精品国产综合久久久蜜| 欧美精品性做久久久久久| 有关日本黄色录像的视频| 交换夫妇4中文字幕| 热精品韩国毛久久久久久| 一级做a爱过程免费视频俩| 69亚洲一级黄片| 中国女人日逼免费片| 一级毛片完整版免费播放一区| 大鸡扒干美女BB直流水| 精品一二三四区中文字幕| 日本韩国国产精品一区|