欧美人妻精品一区二区三区99,中文字幕日韩精品内射,精品国产综合成人亚洲区,久久香蕉国产线熟妇人妻

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 1

Spherical Cast Tungsten Carbide Powder is a novel type of highly wear-resistant ceramic particle material. Compared to traditional tungsten carbide, spherical cast tungsten carbide possesses two significant advantages. Firstly, it has a regular spherical appearance with good powder flowability and wetting properties. When used as an additive particle, it exhibits excellent compatibility with the surrounding structure, reducing stress concentration. Secondly, the internal structure of the tungsten carbide particles is dense, exhibiting good toughness, fine grain size, high hardness, and excellent wear resistance as a coating. It is less prone to fracture under load.

Due to its outstanding performance, spherical cast tungsten carbide powder is gradually replacing traditional tungsten carbide powder in surface protection applications for mining machinery, petroleum machinery, construction industry, and foundries. It significantly enhances the wear resistance, corrosion resistance, and oxidation resistance of components, thereby extending their service life.

The chemical composition, microscopic morphology, microstructure, microhardness, and other powder properties of spherical cast tungsten carbide powder prepared by different methods will be investigated below.

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 2

1.Chemical composition of sample carbide powder

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 3

The table above shows the chemical composition of spherical cast tungsten carbide powder samples prepared by different methods. It can be observed that the main components of spherical cast tungsten carbide powder are tungsten (W) and carbon (C), with trace amounts of iron (Fe), vanadium (V), chromium (Cr), and niobium (Nb). The ideal composition of spherical cast tungsten carbide should consist of eutectic WC and W2C phases, with a eutectic temperature of 2525 ℃ and a carbon content of 3.840% (mass fraction) at the eutectic point. From the data in the table, it can be seen that the spherical cast tungsten carbide powder prepared by the plasma rotating electrode atomization method has the smallest deviation from the theoretical carbon content and the lowest free carbon content. On the other hand, the powder obtained from the induction melting and atomization method shows the largest deviation from the theoretical carbon content, with a difference of 0.170% (mass fraction). This is likely due to the use of graphite tube heating in the induction melting process, which can increase the carbon content. Therefore, compared to other methods, the plasma rotating electrode atomization method can more accurately control the carbon content of spherical cast tungsten carbide powder, preventing over-eutectic and sub-eutectic reactions caused by carburization and decarburization, and achieving a near-perfect eutectic microstructure. This is crucial for improving the microstructure and properties of spherical cast tungsten carbide.

2.Microscopic morphology

fig1.The microstructure of spherical cast tungsten carbide powder samples
fig1.The microstructure of spherical cast tungsten carbide powder samples

The figure above shows the microstructure of spherical cast tungsten carbide powder prepared by different methods. It can be observed that the spherical cast tungsten carbide powder obtained from all three methods exhibits a regular and smooth near-spherical shape.

The cross-sectional images of spherical cast tungsten carbide powder
fig.2 The cross-sectional images of spherical cast tungsten carbide powder

The figure above shows cross-sectional photographs of spherical cast tungsten carbide powder prepared by different methods. From (a) and (b), it can be observed that the particles of spherical tungsten carbide powder prepared by plasma rotating electrode atomization method have a dense internal structure with almost no defects. However, from (c) and (d), it can be seen that spherical tungsten carbide powder prepared by plasma melting and atomization as well as induction melting and atomization methods have some noticeable pores or hollow particles within their internal structure. The main reason for this is that the crushed tungsten carbide powder used as raw material in the above-mentioned methods may contain residual pores from the casting process. During the short-duration plasma or induction heating process, it becomes challenging for the internal part of the crushed tungsten carbide powder to fully melt, resulting in the presence of some pores within the particles.

3.Microstructure

the microscopic structure of spherical cast tungsten carbide powder samples
fig3. the microscopic structure of spherical cast tungsten carbide powder samples

The figure above displays microscopic images of the microstructure of spherical cast tungsten carbide powder particles prepared by different methods after corrosion. It can be observed that the internal structure of the particles in all three methods primarily consists of a typical fine needle-like eutectic structure of WC and W2C phases. Compared to plasma melting and atomization and induction melting and atomization methods, the eutectic microstructure of spherical cast tungsten carbide powder obtained by plasma rotating electrode atomization method appears to be finer and denser. This is because, in contrast to plasma melting and atomization and induction melting and atomization methods, plasma rotating electrode atomization method fully melts the tungsten carbide raw material rod and rapidly solidifies it under the centrifugal force. The higher undercooling during the crystallization of the molten tungsten carbide results in more rapid nucleation and a greater number of crystal nuclei formation, leading to a finer eutectic microstructure.

4.Microhardness

The table below shows the average microhardness of spherical cast tungsten carbide powder prepared by different methods. It can be observed that the microhardness of the spherical cast tungsten carbide powder obtained from all three methods is above 2800 HV0.1. Among them, the powder produced by the plasma rotating electrode atomization method exhibits the highest microhardness, reaching 3045 HV0.1. This is mainly due to the finer and denser eutectic microstructure within the spherical cast tungsten carbide powder obtained by the plasma rotating electrode atomization method.

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 4

5.Other physical properties

The table below presents the flowability and tap density values of spherical cast tungsten carbide powder prepared by different methods. It can be observed that the powder obtained from the plasma rotating electrode atomization method has the poorest flowability and the lowest tap density. On the other hand, the powder obtained from the induction melting and atomization method exhibits the best flowability and the highest tap density.

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 5

Conclusione

(1) The spherical cast tungsten carbide powder prepared by the plasma rotating electrode atomization method exhibits the smallest deviation from the theoretical carbon content and eutectic carbon content, with the lowest free carbon content and relatively low impurity content.

(2) The internal structure of the spherical tungsten carbide powder particles obtained by the plasma rotating electrode atomization method is dense, with almost no defects. The eutectic microstructure is finer and denser. On the other hand, the particles obtained by plasma melting and atomization as well as induction melting and atomization methods show some noticeable pores or hollow particles within their internal structure.

(3) All three methods result in spherical cast tungsten carbide powder primarily consisting of WC and W2C phases.

(4) The microhardness of the spherical cast tungsten carbide powder obtained by all three methods is above 2800 HV0.1. Among them, the powder produced by the plasma rotating electrode atomization method exhibits the highest microhardness, reaching 3045 HV0.1. The powder obtained by the induction melting and atomization method shows good flowability and the highest tap density.

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 6

The performance study of spherical cast tungsten carbide powder prepared by the 3 methods 7

 

 

 

 

Luglio 16, 2023

Hello. I work in the aviation sector and we are metal strip drawing SS aviation grade metal and cannot seem to find a carbide that gives us the toughness and long wear properties that normal carbide would provide with regular tungsten carbide used in metal drawing of softer materials?Would you have a supplier list of companies that provide this new type of carbide? Regards

Agosto 3, 2023

Hello Dale,
Thank you for leaving a comment!
Could you please send us an inquiry to [email protected]?
Distinti saluti,

Lascia un commento

Il tuo indirizzo email non sarà pubblicato. I campi obbligatori sono contrassegnati *

国产免费无码一区二区视频无码| 女人扒开腿让我舔十八禁| 激情久久久久久久久久久| AV无码超清破解版流出| 欧美 日韩 国产 自拍| 国语自产免费精品视频在| 大胸美女被c的嗷嗷叫视频| 骚逼被操视频拳交| 插BB流水水视频| aaa啊啊啊黄片| 差鸡巴没码在线观看| 尤物AV无码国产在线看| 国产综合精品一区二区青青| 爽妇网国产精品24| 中文字幕一高清免费视频| 中文字幕不卡一区二区免| 欧美激情在线播放第一页| 99久久精品国产一区二区成人了| 欧美一级淫片免费播放口| 日韩午夜精品中文字幕| 成人av大全免费一区二区三区| 久久亚洲精品无码AV宋| 亚洲精品一区二区精华液| 操的我的逼逼好爽好多水| 几把日逼嗯嗯视频| 九热中文字幕在线| 男女插插调教骚逼| 国产精品白浆一区二区三区| 大鸡巴插我在线观看| 黄色软件大屌怒戳粉嫩小穴| 在线12萝自慰喷水| 精品日韩欧美精品日韩| 久久久久国产AV成人片| 操美女逼逼色逼网| 一级风流国产片a级| 亚洲色欲久久久久综合网| 女人被大鸡吧操逼| 丝袜片一区二区三区四区五区| 免费女人男人肏逼| 欧美黄色三级成人小视频| 久久综合色伊人九色91|